How to thread a brother vx710 sewing machine

How to thread a brother vx710 sewing machine how to#
How to thread a brother vx710 sewing machine Manual Pdf#
How to thread a brother vx710 sewing machine install#
How to thread a brother vx710 sewing machine manual#
How to thread a brother vx710 sewing machine trial#

Make sure that the end of the thread comes out from the cover toward the rear of the machine. Put the projection into the race retainer groove and push closed. If the thread is not correctly inserted through the tension-adjusting spring of the bobbin case, it may cause incorrect thread tension.Р”Р„t this time, check that the bobbin easily rotates counterclockwise. Hold the end of the thread and push the bobbin down with your finger and pass the thread through the slit. Pull the thread toward you to cut it with the cutter (marked 3).Р”Тђ. While lightly holding down the bobbin with your right hand as shown in the image below, guide the thread through the slit (marked 1 & 2). For models equipped with a quick-set bobbin If the thread unrolls in the wrong direction, it may cause the thread tension to the incorrect or break the needle. This is the best sewing foot for inserting zippers, snap tape, and more. Put the bobbin in so the thread comes out in the direction shown by the arrow.Р”В¬AUTION: Make sure you set the bobbin so the thread unrolls in the right direction. Brother VX 710 Sewing Machine Adjustable Zip / Zipper Foot. Remove the bobbin cover by sliding it and lift toward you.Р”В¤.

Raise the needle by turning the handwheel toward you (counterclockwise) and raise the presser foot lever.Р”Р€. Prepare the bobbin wound properly before threading the lower thread.Р”Сћ.

How to thread a brother vx710 sewing machine manual#

Refer to your owners manual for the correct threading process, as each model may have a slightly different set of instructions. If you accidentally step on the foot controller and the machine starts to sew, you could be injured.Р”РЋ. Ensure that the Elna sewing machine top thread is correctly threaded from the thread spool on top of the machine down through the tension disks, down and up through the thread take-up mechanism and through the needle.

How to thread a brother vx710 sewing machine how to#

How to insert the bobbin into the bobbin caseР”В¬AUTION: Make sure you turn off the machine while threading.

Sewing machines were invented during the first Industrial Revolution to. A sewing machine is a textile machine used to stitch fabric,paper,card and other material together with thread. Brother 920D Serger Instruction Manual, 57 Pages. Any mechanical or electromechanical device used to stitch cloth or other material normally uses two threads to form lock stitches. Service Manual, Brother 920D No Longer Available. Item P-IMB-920D Condition Brand New No Longer Available.

How to thread a brother vx710 sewing machine Manual Pdf#

Make sure that you fit the bobbin case properly, otherwise the needle may break. Brother 920d Manual Download Instruction Manual, Brother 920D. Brother PS-3700 Sewing Machine Instruction Manual Pdf 4.99 Download Brother VX 1400 Sewing Machine Instruction Manual VX1400 4.

How to thread a brother vx710 sewing machine install#

Make sure that you install the needle plate securely.Р”В¬AUTION: Never use a bobbin case that is scratched, otherwise the upper thread may become tangled, the needle may break or sewing performance may suffer.Р’В For a new bobbin case (part # XE9326001), contact your nearest authorized service center. Make sure that the indicated points are aligned before installing the bobbin case.Р”РЃ.Р’В Install the needle plate, and then tighten the screws. Insert the bobbin case so that the mark on the bobbin case aligns with the mark on the machine. Lift up the needle plate and then slide the needle plate to the left to remove it.Р”Тђ.Р’В Grasp the bobbin case and then pull it out to the left.Р”В¦.Р’В Use the cleaning brush or a vacuum cleaner to remove any dust from the race and its surrounding area.Р”В¬AUTION: Do not put oil on the bobbin case.Р”В§.

How to thread a brother vx710 sewing machine trial#

To solve the problem, I had to remove the needle plate cover, take out the bobbin casing and place it back at the right position (some trial and error here).2.Р’В Raise the needle and the presser foot.Р”Р€.Р’В Loosen the presser foot screw and the needle clamp screw to remove the presser foot holder and the needle.Р”В¤.Р’В Using the oval screwdriver, remove the two screws. And sometimes, when the needle gets stuck in the bobbin casing, it will get shifted and mess up the tensions, causing the upper thread to get entangled. If adjusting tensions for both the upper thread and bottom thread are not helping, it might be that the bobbin casing is not sitting right in the bobbin casing holding area.Р”Р‡or some of our Brother machines, we can actually remove the bobbin casing. If that still doesn't work, then adjust the tension of the bobbin thread. Next, try dropping the tension of your upper thread and see if it sews better. Hey BoscAna, are you using a Brother machine? Is it a new machine? Also, are you using the right needle for the fabric and thread?Р”Р‡irstly, do make sure that your bobbin thread is wound correctly on your bobbin and that the bobbin thread is also under the metal prong of the bobbin casing.